Deployers

Every pump.fun token is launched by a wallet, its deployer. Prysm lets you look a deployer up and follow it:

Scan — see the tokens a wallet has launched and how they did.
Track — get an alert when that wallet launches a new token.

Deployers are Solana / pump.fun only. You can send a wallet address on its own, or paste a pump.fun or Solscan link and Prysm takes the address from it. /deployer shows both commands and what you’re tracking.

Scan a deployer

Send /scandeployer <address> (or /deployerscan). It works in your DM and in groups.

In your DM the scan fills in on screen while it runs: first the launch counts, then the table once the market caps and highs are in. In a group, Prysm posts a short Scanning deployer… line and turns it into the table.

Deployer launches

yHCx…6PRe
Deployed 965 · Bonded 129 · Last 15h ago

# TICKER      MCAP    ATH  AGE
1 TOOMUCH     $30K  $380K  15h
2 COPPERINU  $1.1M  $4.1M   1d
3 ALON       $890K   ~$1M  2mo

Chart : 1 2 3

[ Next ▶ ]
[ ➕ Track deployer ]

Deployed / Bonded / Last — how many tokens the wallet has launched in total, how many of them graduated off the bonding curve, and how long ago its latest launch was.
# — newest launch first. The table covers the wallet’s most recent launches, so a very busy wallet’s oldest tokens may not be listed.
MCAP — current market cap. — means it has no market right now.
ATH — the highest market cap the token reached. A ~ in front means only an estimate was available; the real high was at least that.
AGE — time since launch (15h, 1d, 2mo).
Chart — tap a number to open that token’s chart in the chat’s chart provider.

Use ◀ Prev and Next ▶ to page through. The buttons stop working after about an hour; send the command again to get a fresh scan.

Reply	Meaning
`Please wait a few seconds before scanning again.`	You scanned very recently. Wait a moment.
`Scanner is busy — try again in a moment.`	Too many scans are running. Try again shortly.
`No pump.fun launches found for this deployer.`	The wallet hasn’t launched anything on pump.fun.
`Send a valid Solana deployer address …`	The address or link wasn’t a Solana wallet.
`partial history` note	Part of the history couldn’t be loaded. Scan again later for the full list.

Track a deployer

Two ways to start:

Tap ➕ Track deployer under a scan. It turns into 🛑 Stop tracking, which undoes it.
Send /trackdeployer <address>.

In your DM the deployer is tracked for you. In a group it’s tracked for the group, and alerts post in the topic where it was set up. In groups, only admins can track or stop tracking deployers.

The first deployer you track switches deployer alerts on for you (or for the group).

What an alert looks like

🪙 Moon Cat ($MCAT)

🚀 New launch by yHCx…6PRe
7xKp…pump · MCap: $6.2K

The token’s name (tap it for the chart) and its $SYMBOL.
New launch by the deployer. If a different wallet sent the launch, it’s shown after it as (via …).
The new token’s short address and its market cap, when it’s known yet.

Manage tracking

/deployer — lists the deployers tracked here, shows Tracked N/limit and whether alerts are on, with a ✖ button to stop each one.
/untrackdeployer <address> — stop tracking one.
Settings → Experimental → Deployer Tracking — the full controls (in a group, /settings is for admins):
- On / Off — switch all deployer alerts here on or off. Your tracked list is kept either way.
- Daily cap — the most deployer alerts per day: 2, 5, 10 or 25. The count resets every day at midnight UTC.
- ✖ rows to remove single deployers.

Limits

You can track up to 3 deployers in your DM, and a group up to 3. At the limit, remove one with /deployer before adding another. Contact the bot owner for a higher limit.